DJTechTools Jun 8, 2016

Many DJs know all about different types of music, but it’s not too uncommon to find DJs who know absolutely nothing about how sound actually works. In this two-part series, we get a little nerdy and offer an introduction to basic audio electrical engineering for DJs. At the end of it, we hope you’ll understand a bit better what’s going on ?under the hood? of your DJ hardware! This first part covers how analog sound becomes digital audio – and what sample and bit rates really are.

This two-part article series was crafted by guest contributor Ryan Mann, an Energy Engineering student at UC Berkeley.

To start things out, let?s talk about the difference between the analog sound coming out of speakers, and the digital music files in your computer:

Analog Sound

Sound itself is the propagation of pressure waves through a compressible medium. The sounds we hear are a continuous, smooth analog signal.This signal can be decomposed (using something called the Fourier Transform) into a combination of sinusoids (elements of the signal) with different frequencies, amplitudes, and phases.

The Fourier Transform

The Fourier Transform – from combined sound into individual waves

Frequency is the duration of each cycle, measured in Hertz (Hz), where 1 Hz is 1 cycle per second. The human ear can hear frequencies between 20 Hz and 20,000 Hz (20 kHz), and each part of your ears’cochlea responds to a different frequency.

amplitude-phase

Amplitude is the height of the wave, or the maximum pressure during the cycle. Pressure is measured with a bunch of different units, and the amount of power required to produce a certain amplitude over an area is measured in Watts (W), but volume is usually measured in decibels (dB), which compares the power of the sound to a power of 0.001 W using a logarithmic scale.

Phase is the timing of one wave relative to another. If there are two waves with the same frequency, they may or may not reach their peak at the same time. Phase measures the time between the peak of one wave and the peak of another, if any.

Digital Music Files are not stored as continuous analog signals, but as a large number of digital bits able to be read by a computer (in binary; 1 or 0).Each 1 or 0 is called a ?bit.? 8 bits make up a ?byte.?

Analog-to-Digital Conversion (ADC)

adc

Analog sound is converted to a digital file when recording live instruments, or when recording a mix from an analog mixer into your computer. The Analog-to-Digital Conversion (ADC) process occurs as follows:

  • There is some sort of physical phenomenon to be measured – in this case, sound (or pressure).
  • A sensor (in this case, a microphone) converts the sound into a continuous voltage signal.
  • The ADC sound card samples this signal, sorts the sampled value into a ?bin?, and records this value as binary ?bits.?

Digital-to-Analog Conversion (DAC)

DAC

For the opposite process, audio starts asmusic file stored as digital bits. A DAC soundcard (like in amixer, DJ controller, etc) converts the digital voltage values into a slightly ?choppy? continuous signal. Then, an actuator (here, a speaker) converts the signal into sound.

The quality of the output is determined by the quality of the original file, and the resolution of the DAC in the soundcard – for example:

  • playing a YouTube rip on a cheap Chromebook laptop might mean a 96 kbps file and a 16-bit, 48 kHz soundcard
  • alternately, playing a lossless FLAC file on the brand-new CDJ-TOUR1 would mean a 1411 kbps song and a 24-bit, 96 kHz Wolfson DAC

Bits

The number of bits used in analog-to-digital conversion determines the accuracy with which the digital signal replicates the actual analog value at any given point.

1-bit-adc

For example, a 1-bit ADC (pictured above) is only capable of recording a 1 (full voltage) or a 0 (no voltage). So anything in between has to get ?rounded? into the closest available category, meaning there will be a large jump at the halfway point.

16-vs-3-bit-res

For every bit that?s added, the resolution (number of steps) doubles, so it?s possible to get a nearly perfect representation of the signal with only a relatively small number of bits:

  • 1 bit = 2 steps
  • 3 bits = 8 steps
  • 16 bits = 65,536 steps
  • 24 bits = 16,777,216 steps

Sampling Rates

Time resolution (the sampling rate) is just as important as amplitude resolution (the number of bits).A higher sampling rate means that the original analog signal is replicated more accurately.

But if the sampling rate is too high, it uses a lot of processor power and memory.So what?s the right sampling rate to use?Nyquist-Shannon Sampling Theorem states that the sampling rate must be at least twice the frequency of the highest frequency found in the signal.

samples-per-cycles

In the above diagram, you can see how 1 sample per cycle would not be enough to capture what’s going on, and 2 samples per cycle would be theminimum for recording the signal accurately. At two samples/cycle, the samples must be at the min and max points of the wave, otherwise it will record the right frequency but wrong amplitude and phase.

Sampling at higher than 2 samples / cycle smooths out the waveform and increases the quality of the audio – but at the cost of more processor power and storage space.

CD-quality audio is recorded at a little higher than the Nyquist minimum sample rate for the highest frequency that people can hear. (The maximum audible frequency for most people is 20 kHz, and CDs are recorded at 44.1 kHz).

Bitrate + Compression

Most digital audio files are not as high-resolution as a lossless audio file like those found on a CD.

There are a number of different algorithms and file formats to compress the audio file in order to make it easier to transfer and store. However, unlike on ?Silicon Valley?, there is no such thing as truly lossless compression. The challenge is to reduce the file size while retaining as much audio quality as possible.

In general, this means reducing the sampling rate and bits. This means that higher-frequency sounds are not converted accurately, or are filtered out entirely to prevent aliasing.

What happens when audio files are drastically compressed (CD audio on top, 96 kbps MP3 on bottom)

What happens when audio files are drastically compressed (CD audio on top, 96 kbps MP3 on bottom)

The bit rate of a song (measured in kbps – kilobits per second) is equal to the number of bits, times the sampling rate. Some DJs swear by only playing lossless WAV or AIFF files, but it?s generally fine to play 192 kbps VBRs (variable bit rate), 256 kbps AACs (iTunes Store purchases), or 320 kbps MP3s (cheapest Beatport option, most downloads) even on a large club speaker system.

Recordings that are 128 kbps and below should generally be avoided. This is the sound quality of a YouTube or SoundCloud rip, or an old Napster download

  • 1411 kbps (CD/WAV/AIFF) = 16 bits x 44.1 kHz x 2 stereo channels
  • 320 kbps = 16 bits x 10 kHz x 2 stereo channels
  • 256 kbps AAC = 16 bits x 8 kHz x 2 stereo channels 128 kbps MP3 = 16 bits x 4 kHz x 2 stereo channels

Read more: A DJ’s Guide To Audio Files + Bit Rates

In part two of this series, we’ll cover the inner workings of DJ equipment – how they manipulate digital and/or analog audio, and what filters and EQ knobs do on an electrical level. Stay tuned!

Ryan Mann is a guest contributor to DJ Techtools, and helps to leadelecTONIC, a student group at UC Berkeley dedicated to promoting electronic music.

The post Electrical Engineering For DJs Part 1: Analog/Digital Audio, Bit and Sample Rates appeared first on DJ TechTools.