On the new PLAYdifferently Model 1 mixer designed by Richie Hawtin, thereâs a unique approach to the actual mixing section. Instead of a âtraditionalâ 3-band EQ, there are two filters and a âparametric EQâ. But for many DJs, the only way theyâll be able to try this style of mixing is by shelling out over $3,000 on the mixer â so DJ Soo has created an Ableton device that allows anyone to try out a very similar workflow. Keep reading for a free download!
A Unique EQ Section On PLAYdifferentlyâs Model 1
With the much-hyped Ritchie Hawtin and Andy Rigby-Jones PLAYdifferently Model 1 mixer making its official announcement last week, weâve gained another high-end audiophile mixer designed for a niche crowd of sound quality obsessed DJs. Alongside the Rane MP2015, Vestax/STPâs Phoenix, and the Funktion-One FF6.2, the Model 1 appeals to those looking for a throwback to the classic, rotary-style mixers of the past, but with modern features and design in mind.
Perhaps one of the most obvious changes on the Model 1 are the EQ controls, which are different from just about any mixer on the market:
Rather than the standard 3 or 4 pots to allow either cutting or gaining a frequency spectrum band (generally highs, mids, and lows), the Model 1 uses high pass and low pass filters to cut out frequencies and then a single cut/boost knob alongside a sweepable frequency knob for the mids. Although this is fairly typical in studio and live sound mixing consoles (generally used to isolate feedback-causing frequencies and cutting them), it seems like a first for a DJ mixer.
I was really interested in trying out this unique EQ setup, but shelling out $3600 just for the novelty of experimenting with the design wasnât happening. Fortunately, the PLAYdifferently promotional literature â and even the labels on the mixer itself â is fairly specific with its parameters. Combined with the powerful macro features in Ableton, itâs not hard to create a reasonable emulation of the EQs using stock Ableton plugins.
Making the Model 1 EQ in Ableton
As mentioned, the Model 1 EQ consists of two filters and an EQ with a frequency sweep. Weâll start by adding the relevant Ableton plugins to controls those parameters:
- Start by loading up an Auto Filter, an EQ8, another Auto filter, and a Utility
- Select all the plugins and group all the effects in a single Effect Rack by right-clicking and selecting Group
- Start assigning controls to Macro knobs:
Low Pass Filter: Letâs map the Low Pass Filter first:
- On the Auto Filter, switch the Filter Slope to 12 (see below) and turn the Resonance down to 0.
- Assign the Freq knob to Macro 1 by right-clicking on the Filter Freq knob and assigning it to Macro 1.
- For the most amount of transparency in the sound, we want the plugin to fully bypass when Low Pass is completely open â so assign the plugin on/off switch to Macro 1 as well.
- Rename the plugin and Macro 1 to âLPFâ by right-clicking it and selecting âRenameâ
Sculpting EQ: Next, weâll map the sweepable EQ:
- Turn off all the filters on the EQ except for one Bell filter:
- Select the activated EQ filter and map the Gain to Macro 2
- Map the Freq knob to Macro 3
- The Model 1 promotional material states that the mid EQ has a âwideâ Q, so set the Q knob to a lower number â I used .5
- Rename the plugin to âSCULPTâ and Macro 2 to âCut/Boostâ and Macro 3 to âFREQâ
High Pass Filter
- First, switch the Auto Filter to a High Pass filter
- As with the LPF, change the Slope to 12 and the Res to 0
- Map the Freq knob to Macro 4, as well as the deviceâs on/off button
- Rename the plugin and Macro 4 to âHPFâ
- On the Utility, map the Gain knob to Macro 6
- Since the Gain knob does not completely mute the sound (rather bottoms out at -35db), we should also map the Mute button to the same Macro, so that when the knob is turned all the way down, the volume is completely cut off.
So once all of the Macros are assigned, we need to adjust the mappings so they function according to the Model 1 parameters. This will make sure that the final result is similar to the Model 1 in terms of what youâre able to control.
- Click on the Map button at the top of the Rack to open the Macro Mappings window
- On the SCULPT Frequency parameter, set the Min to 70 Hz and the Max to 7.00 kHz
- On the SCULPT Gain parameter, leave the Min to -15 dB, and set the Max to +6 dB
- On the LPF Device On parameter, set the Min to 127 and the Max to 126
- On the LPF Frequency parameter, set the Min to 500 Hz and the Max to 19.9 Hz
- On the HPF Device On parameter, set the Min to 1 and the Max to 0
- On the HPF Frequency parameter, set the Min to 26 Hz and the Max to 1.0 kHz
- On the Utility Gain parameter, set the Min to -35 dB and the Max to +8 dB
- On the Utility Mute parameter, set the Min to 0 and the Max to 1
Youâre done! This is now a reasonable facsimile of the PLAYDifferently Model 1 EQ section recreated in Ableton. You can map some more controls if desired: I mapped the Resonance controls of each filter to Macros as well as mapping the Q control on the EQ8 to its own knob to allow for greater control over the audio. You can also adjust the slope of the Filter cutoffs and filter types to taste.
The best way to play around with this would be to map to a physical controller with knobs â Midi Fighter Twister would work exceptionally well for a four-channel version.
This isnât a frequency-for-frequency exact recreation of the Model 1, and due to limitations in the Ableton mapping design, finding the 0-point on some of these controls is a little tricky, but it will give you an idea of how the unique EQ section works.
The post Recreating The EQ Section Of Richie Hawtinâs Model 1 Mixer In Ableton Live appeared first on DJ TechTools.